Installation Requirements
The Whirlpool AWG 912 S PRO must be installed on a
level, stable surface capable of supporting its full operating weight.
Ensure adequate ventilation clearance as
specified in the installation diagram on page 4.
Connect to a correctly rated power supply -- refer to the data
plate for voltage and amperage requirements.
Plumbing connections (where applicable) must comply with local
building regulations and be completed by a qualified professional.
First Use
Before first
use, run the Whirlpool AWG 912 S PRO through an empty cycle to clean the drum and internal components.
Remove all
packaging materials, transit bolts, and protective films before operating.
Set the clock and any regional settings
via the control panel as described in Chapter 2.
Register your appliance on the Whirlpool website to activate the
full manufacturer warranty.
Operating Programs
The Whirlpool AWG 912 S PRO offers a range
of programmes designed for different load types and energy efficiency levels.
Eco mode reduces energy and water
consumption by up to 40% compared to standard cycles.
Quick wash cycles are suitable for lightly soiled loads and
complete in under 30 minutes.
Refer to the programme guide in Section 3 for a full list of settings, temperatures,
and spin speeds.
Cleaning & Maintenance
Clean the door seal and detergent drawer of your
Whirlpool AWG 912 S PRO monthly to prevent mould and odour build-up.
Run a maintenance wash at 60 degrees Celsius
with a drum cleaning tablet every 3 months.
The filter should be checked and cleaned after every 10 cycles to
maintain drainage performance.
Descale the appliance every 3 months in hard water areas using a Whirlpool-approved
descaling agent.
Error Codes & Troubleshooting
Error codes on the Whirlpool AWG 912 S PRO
display indicate specific faults -- consult the error code table in Appendix A.
E1/F1 errors typically relate to
water supply issues -- check the inlet hose and water pressure.
If the appliance does not start, verify the door
is fully closed and the child lock is not activated.
For persistent faults not resolved by the troubleshooting
guide, contact Whirlpool customer service with your model and serial number.
Whirlpool / Appliance
Installation Requirements
The Whirlpool AZB9CD must be installed on a level,
stable surface capable of supporting its full operating weight.
Ensure adequate ventilation clearance as specified
in the installation diagram on page 4.
Connect to a correctly rated power supply -- refer to the data plate for
voltage and amperage requirements.
Plumbing connections (where applicable) must comply with local building
regulations and be completed by a qualified professional.
First Use
Before first use, run
the Whirlpool AZB9CD through an empty cycle to clean the drum and internal components.
Remove all packaging
materials, transit bolts, and protective films before operating.
Set the clock and any regional settings via the
control panel as described in Chapter 2.
Register your appliance on the Whirlpool website to activate the full
manufacturer warranty.
Operating Programs
The Whirlpool AZB9CD offers a range of programmes
designed for different load types and energy efficiency levels.
Eco mode reduces energy and water consumption by
up to 40% compared to standard cycles.
Quick wash cycles are suitable for lightly soiled loads and complete in
under 30 minutes.
Refer to the programme guide in Section 3 for a full list of settings, temperatures, and spin
speeds.
Cleaning & Maintenance
Clean the door seal and detergent drawer of your Whirlpool
AZB9CD monthly to prevent mould and odour build-up.
Run a maintenance wash at 60 degrees Celsius with a drum
cleaning tablet every 3 months.
The filter should be checked and cleaned after every 10 cycles to maintain
drainage performance.
Descale the appliance every 3 months in hard water areas using a Whirlpool-approved
descaling agent.
Error Codes & Troubleshooting
Error codes on the Whirlpool AZB9CD display
indicate specific faults -- consult the error code table in Appendix A.
E1/F1 errors typically relate to water
supply issues -- check the inlet hose and water pressure.
If the appliance does not start, verify the door is
fully closed and the child lock is not activated.
For persistent faults not resolved by the troubleshooting guide,
contact Whirlpool customer service with your model and serial number.
Whirlpool / Appliance
Installation Requirements
The Whirlpool DDLX90117 must be installed on a level,
stable surface capable of supporting its full operating weight.
Ensure adequate ventilation clearance as specified
in the installation diagram on page 4.
Connect to a correctly rated power supply -- refer to the data plate for
voltage and amperage requirements.
Plumbing connections (where applicable) must comply with local building
regulations and be completed by a qualified professional.
First Use
Before first use, run
the Whirlpool DDLX90117 through an empty cycle to clean the drum and internal components.
Remove all packaging
materials, transit bolts, and protective films before operating.
Set the clock and any regional settings via the
control panel as described in Chapter 2.
Register your appliance on the Whirlpool website to activate the full
manufacturer warranty.
Operating Programs
The Whirlpool DDLX90117 offers a range of
programmes designed for different load types and energy efficiency levels.
Eco mode reduces energy and water
consumption by up to 40% compared to standard cycles.
Quick wash cycles are suitable for lightly soiled loads and
complete in under 30 minutes.
Refer to the programme guide in Section 3 for a full list of settings, temperatures,
and spin speeds.
Cleaning & Maintenance
Clean the door seal and detergent drawer of your
Whirlpool DDLX90117 monthly to prevent mould and odour build-up.
Run a maintenance wash at 60 degrees Celsius with
a drum cleaning tablet every 3 months.
The filter should be checked and cleaned after every 10 cycles to maintain
drainage performance.
Descale the appliance every 3 months in hard water areas using a Whirlpool-approved
descaling agent.
Error Codes & Troubleshooting
Error codes on the Whirlpool DDLX90117
display indicate specific faults -- consult the error code table in Appendix A.
E1/F1 errors typically relate to
water supply issues -- check the inlet hose and water pressure.
If the appliance does not start, verify the door
is fully closed and the child lock is not activated.
For persistent faults not resolved by the troubleshooting
guide, contact Whirlpool customer service with your model and serial number.
Whirlpool / Appliance