Installation Requirements
The Dyson 360 Vis Nav must be installed on a level,
stable surface capable of supporting its full operating weight.
Ensure adequate ventilation clearance as specified
in the installation diagram on page 4.
Connect to a correctly rated power supply -- refer to the data plate for
voltage and amperage requirements.
Plumbing connections (where applicable) must comply with local building
regulations and be completed by a qualified professional.
First Use
Before first use, run
the Dyson 360 Vis Nav through an empty cycle to clean the drum and internal components.
Remove all packaging
materials, transit bolts, and protective films before operating.
Set the clock and any regional settings via the
control panel as described in Chapter 2.
Register your appliance on the Dyson website to activate the full
manufacturer warranty.
Operating Programs
The Dyson 360 Vis Nav offers a range of
programmes designed for different load types and energy efficiency levels.
Eco mode reduces energy and water
consumption by up to 40% compared to standard cycles.
Quick wash cycles are suitable for lightly soiled loads and
complete in under 30 minutes.
Refer to the programme guide in Section 3 for a full list of settings, temperatures,
and spin speeds.
Cleaning & Maintenance
Clean the door seal and detergent drawer of your
Dyson 360 Vis Nav monthly to prevent mould and odour build-up.
Run a maintenance wash at 60 degrees Celsius with a
drum cleaning tablet every 3 months.
The filter should be checked and cleaned after every 10 cycles to maintain
drainage performance.
Descale the appliance every 3 months in hard water areas using a Dyson-approved descaling
agent.
Error Codes & Troubleshooting
Error codes on the Dyson 360 Vis Nav display indicate
specific faults -- consult the error code table in Appendix A.
E1/F1 errors typically relate to water supply
issues -- check the inlet hose and water pressure.
If the appliance does not start, verify the door is fully
closed and the child lock is not activated.
For persistent faults not resolved by the troubleshooting guide,
contact Dyson customer service with your model and serial number.
Dyson / Appliance
Installation Requirements
The Dyson Airwrap HS05 Complete must be installed on a
level, stable surface capable of supporting its full operating weight.
Ensure adequate ventilation clearance as
specified in the installation diagram on page 4.
Connect to a correctly rated power supply -- refer to the data
plate for voltage and amperage requirements.
Plumbing connections (where applicable) must comply with local
building regulations and be completed by a qualified professional.
First Use
Before first
use, run the Dyson Airwrap HS05 Complete through an empty cycle to clean the drum and internal components.
Remove
all packaging materials, transit bolts, and protective films before operating.
Set the clock and any regional
settings via the control panel as described in Chapter 2.
Register your appliance on the Dyson website to activate
the full manufacturer warranty.
Operating Programs
The Dyson Airwrap HS05 Complete offers a
range of programmes designed for different load types and energy efficiency levels.
Eco mode reduces energy and
water consumption by up to 40% compared to standard cycles.
Quick wash cycles are suitable for lightly soiled
loads and complete in under 30 minutes.
Refer to the programme guide in Section 3 for a full list of settings,
temperatures, and spin speeds.
Cleaning & Maintenance
Clean the door seal and detergent
drawer of your Dyson Airwrap HS05 Complete monthly to prevent mould and odour build-up.
Run a maintenance wash at
60 degrees Celsius with a drum cleaning tablet every 3 months.
The filter should be checked and cleaned after
every 10 cycles to maintain drainage performance.
Descale the appliance every 3 months in hard water areas using a
Dyson-approved descaling agent.
Error Codes & Troubleshooting
Error codes on the Dyson
Airwrap HS05 Complete display indicate specific faults -- consult the error code table in Appendix A.
E1/F1 errors
typically relate to water supply issues -- check the inlet hose and water pressure.
If the appliance does not
start, verify the door is fully closed and the child lock is not activated.
For persistent faults not resolved by
the troubleshooting guide, contact Dyson customer service with your model and serial number.
Dyson / Appliance
Installation Requirements
The Dyson AM09 Fan Heater must be installed on a level,
stable surface capable of supporting its full operating weight.
Ensure adequate ventilation clearance as specified
in the installation diagram on page 4.
Connect to a correctly rated power supply -- refer to the data plate for
voltage and amperage requirements.
Plumbing connections (where applicable) must comply with local building
regulations and be completed by a qualified professional.
First Use
Before first use, run
the Dyson AM09 Fan Heater through an empty cycle to clean the drum and internal components.
Remove all packaging
materials, transit bolts, and protective films before operating.
Set the clock and any regional settings via the
control panel as described in Chapter 2.
Register your appliance on the Dyson website to activate the full
manufacturer warranty.
Operating Programs
The Dyson AM09 Fan Heater offers a range of
programmes designed for different load types and energy efficiency levels.
Eco mode reduces energy and water
consumption by up to 40% compared to standard cycles.
Quick wash cycles are suitable for lightly soiled loads and
complete in under 30 minutes.
Refer to the programme guide in Section 3 for a full list of settings, temperatures,
and spin speeds.
Cleaning & Maintenance
Clean the door seal and detergent drawer of your
Dyson AM09 Fan Heater monthly to prevent mould and odour build-up.
Run a maintenance wash at 60 degrees Celsius
with a drum cleaning tablet every 3 months.
The filter should be checked and cleaned after every 10 cycles to
maintain drainage performance.
Descale the appliance every 3 months in hard water areas using a Dyson-approved
descaling agent.
Error Codes & Troubleshooting
Error codes on the Dyson AM09 Fan Heater
display indicate specific faults -- consult the error code table in Appendix A.
E1/F1 errors typically relate to
water supply issues -- check the inlet hose and water pressure.
If the appliance does not start, verify the door
is fully closed and the child lock is not activated.
For persistent faults not resolved by the troubleshooting
guide, contact Dyson customer service with your model and serial number.
Dyson / Appliance