Installation Requirements
The Bosch BCM8450UC must be installed on a level, stable
surface capable of supporting its full operating weight.
Ensure adequate ventilation clearance as specified in the
installation diagram on page 4.
Connect to a correctly rated power supply -- refer to the data plate for voltage
and amperage requirements.
Plumbing connections (where applicable) must comply with local building regulations and
be completed by a qualified professional.
First Use
Before first use, run the Bosch
BCM8450UC through an empty cycle to clean the drum and internal components.
Remove all packaging materials,
transit bolts, and protective films before operating.
Set the clock and any regional settings via the control
panel as described in Chapter 2.
Register your appliance on the Bosch website to activate the full manufacturer
warranty.
Operating Programs
The Bosch BCM8450UC offers a range of programmes designed for
different load types and energy efficiency levels.
Eco mode reduces energy and water consumption by up to 40%
compared to standard cycles.
Quick wash cycles are suitable for lightly soiled loads and complete in under 30
minutes.
Refer to the programme guide in Section 3 for a full list of settings, temperatures, and spin
speeds.
Cleaning & Maintenance
Clean the door seal and detergent drawer of your Bosch
BCM8450UC monthly to prevent mould and odour build-up.
Run a maintenance wash at 60 degrees Celsius with a drum
cleaning tablet every 3 months.
The filter should be checked and cleaned after every 10 cycles to maintain
drainage performance.
Descale the appliance every 3 months in hard water areas using a Bosch-approved descaling
agent.
Error Codes & Troubleshooting
Error codes on the Bosch BCM8450UC display indicate
specific faults -- consult the error code table in Appendix A.
E1/F1 errors typically relate to water supply
issues -- check the inlet hose and water pressure.
If the appliance does not start, verify the door is fully
closed and the child lock is not activated.
For persistent faults not resolved by the troubleshooting guide,
contact Bosch customer service with your model and serial number.
Bosch / Appliance
Installation Requirements
The Bosch CTL636ES6 must be installed on a level, stable
surface capable of supporting its full operating weight.
Ensure adequate ventilation clearance as specified in the
installation diagram on page 4.
Connect to a correctly rated power supply -- refer to the data plate for voltage
and amperage requirements.
Plumbing connections (where applicable) must comply with local building regulations and
be completed by a qualified professional.
First Use
Before first use, run the Bosch
CTL636ES6 through an empty cycle to clean the drum and internal components.
Remove all packaging materials,
transit bolts, and protective films before operating.
Set the clock and any regional settings via the control
panel as described in Chapter 2.
Register your appliance on the Bosch website to activate the full manufacturer
warranty.
Operating Programs
The Bosch CTL636ES6 offers a range of programmes designed for
different load types and energy efficiency levels.
Eco mode reduces energy and water consumption by up to 40%
compared to standard cycles.
Quick wash cycles are suitable for lightly soiled loads and complete in under 30
minutes.
Refer to the programme guide in Section 3 for a full list of settings, temperatures, and spin
speeds.
Cleaning & Maintenance
Clean the door seal and detergent drawer of your Bosch
CTL636ES6 monthly to prevent mould and odour build-up.
Run a maintenance wash at 60 degrees Celsius with a drum
cleaning tablet every 3 months.
The filter should be checked and cleaned after every 10 cycles to maintain
drainage performance.
Descale the appliance every 3 months in hard water areas using a Bosch-approved descaling
agent.
Error Codes & Troubleshooting
Error codes on the Bosch CTL636ES6 display indicate
specific faults -- consult the error code table in Appendix A.
E1/F1 errors typically relate to water supply
issues -- check the inlet hose and water pressure.
If the appliance does not start, verify the door is fully
closed and the child lock is not activated.
For persistent faults not resolved by the troubleshooting guide,
contact Bosch customer service with your model and serial number.
Bosch / Appliance
Installation Requirements
The Bosch GIN81AEF0 must be installed on a level, stable
surface capable of supporting its full operating weight.
Ensure adequate ventilation clearance as specified in the
installation diagram on page 4.
Connect to a correctly rated power supply -- refer to the data plate for voltage
and amperage requirements.
Plumbing connections (where applicable) must comply with local building regulations and
be completed by a qualified professional.
First Use
Before first use, run the Bosch
GIN81AEF0 through an empty cycle to clean the drum and internal components.
Remove all packaging materials,
transit bolts, and protective films before operating.
Set the clock and any regional settings via the control
panel as described in Chapter 2.
Register your appliance on the Bosch website to activate the full manufacturer
warranty.
Operating Programs
The Bosch GIN81AEF0 offers a range of programmes designed for
different load types and energy efficiency levels.
Eco mode reduces energy and water consumption by up to 40%
compared to standard cycles.
Quick wash cycles are suitable for lightly soiled loads and complete in under 30
minutes.
Refer to the programme guide in Section 3 for a full list of settings, temperatures, and spin
speeds.
Cleaning & Maintenance
Clean the door seal and detergent drawer of your Bosch
GIN81AEF0 monthly to prevent mould and odour build-up.
Run a maintenance wash at 60 degrees Celsius with a drum
cleaning tablet every 3 months.
The filter should be checked and cleaned after every 10 cycles to maintain
drainage performance.
Descale the appliance every 3 months in hard water areas using a Bosch-approved descaling
agent.
Error Codes & Troubleshooting
Error codes on the Bosch GIN81AEF0 display indicate
specific faults -- consult the error code table in Appendix A.
E1/F1 errors typically relate to water supply
issues -- check the inlet hose and water pressure.
If the appliance does not start, verify the door is fully
closed and the child lock is not activated.
For persistent faults not resolved by the troubleshooting guide,
contact Bosch customer service with your model and serial number.
Bosch / Appliance
Installation Requirements
The Bosch HBG675BS1 must be installed on a level, stable
surface capable of supporting its full operating weight.
Ensure adequate ventilation clearance as specified in the
installation diagram on page 4.
Connect to a correctly rated power supply -- refer to the data plate for voltage
and amperage requirements.
Plumbing connections (where applicable) must comply with local building regulations and
be completed by a qualified professional.
First Use
Before first use, run the Bosch
HBG675BS1 through an empty cycle to clean the drum and internal components.
Remove all packaging materials,
transit bolts, and protective films before operating.
Set the clock and any regional settings via the control
panel as described in Chapter 2.
Register your appliance on the Bosch website to activate the full manufacturer
warranty.
Operating Programs
The Bosch HBG675BS1 offers a range of programmes designed for
different load types and energy efficiency levels.
Eco mode reduces energy and water consumption by up to 40%
compared to standard cycles.
Quick wash cycles are suitable for lightly soiled loads and complete in under 30
minutes.
Refer to the programme guide in Section 3 for a full list of settings, temperatures, and spin
speeds.
Cleaning & Maintenance
Clean the door seal and detergent drawer of your Bosch
HBG675BS1 monthly to prevent mould and odour build-up.
Run a maintenance wash at 60 degrees Celsius with a drum
cleaning tablet every 3 months.
The filter should be checked and cleaned after every 10 cycles to maintain
drainage performance.
Descale the appliance every 3 months in hard water areas using a Bosch-approved descaling
agent.
Error Codes & Troubleshooting
Error codes on the Bosch HBG675BS1 display indicate
specific faults -- consult the error code table in Appendix A.
E1/F1 errors typically relate to water supply
issues -- check the inlet hose and water pressure.
If the appliance does not start, verify the door is fully
closed and the child lock is not activated.
For persistent faults not resolved by the troubleshooting guide,
contact Bosch customer service with your model and serial number.
Bosch / Appliance
Installation Requirements
The Bosch HEB7784H1 must be installed on a level, stable
surface capable of supporting its full operating weight.
Ensure adequate ventilation clearance as specified in the
installation diagram on page 4.
Connect to a correctly rated power supply -- refer to the data plate for voltage
and amperage requirements.
Plumbing connections (where applicable) must comply with local building regulations and
be completed by a qualified professional.
First Use
Before first use, run the Bosch
HEB7784H1 through an empty cycle to clean the drum and internal components.
Remove all packaging materials,
transit bolts, and protective films before operating.
Set the clock and any regional settings via the control
panel as described in Chapter 2.
Register your appliance on the Bosch website to activate the full manufacturer
warranty.
Operating Programs
The Bosch HEB7784H1 offers a range of programmes designed for
different load types and energy efficiency levels.
Eco mode reduces energy and water consumption by up to 40%
compared to standard cycles.
Quick wash cycles are suitable for lightly soiled loads and complete in under 30
minutes.
Refer to the programme guide in Section 3 for a full list of settings, temperatures, and spin
speeds.
Cleaning & Maintenance
Clean the door seal and detergent drawer of your Bosch
HEB7784H1 monthly to prevent mould and odour build-up.
Run a maintenance wash at 60 degrees Celsius with a drum
cleaning tablet every 3 months.
The filter should be checked and cleaned after every 10 cycles to maintain
drainage performance.
Descale the appliance every 3 months in hard water areas using a Bosch-approved descaling
agent.
Error Codes & Troubleshooting
Error codes on the Bosch HEB7784H1 display indicate
specific faults -- consult the error code table in Appendix A.
E1/F1 errors typically relate to water supply
issues -- check the inlet hose and water pressure.
If the appliance does not start, verify the door is fully
closed and the child lock is not activated.
For persistent faults not resolved by the troubleshooting guide,
contact Bosch customer service with your model and serial number.
Bosch / Appliance
Installation Requirements
The Bosch HRA578BS6B must be installed on a level,
stable surface capable of supporting its full operating weight.
Ensure adequate ventilation clearance as specified
in the installation diagram on page 4.
Connect to a correctly rated power supply -- refer to the data plate for
voltage and amperage requirements.
Plumbing connections (where applicable) must comply with local building
regulations and be completed by a qualified professional.
First Use
Before first use, run
the Bosch HRA578BS6B through an empty cycle to clean the drum and internal components.
Remove all packaging
materials, transit bolts, and protective films before operating.
Set the clock and any regional settings via the
control panel as described in Chapter 2.
Register your appliance on the Bosch website to activate the full
manufacturer warranty.
Operating Programs
The Bosch HRA578BS6B offers a range of programmes
designed for different load types and energy efficiency levels.
Eco mode reduces energy and water consumption by
up to 40% compared to standard cycles.
Quick wash cycles are suitable for lightly soiled loads and complete in
under 30 minutes.
Refer to the programme guide in Section 3 for a full list of settings, temperatures, and spin
speeds.
Cleaning & Maintenance
Clean the door seal and detergent drawer of your Bosch
HRA578BS6B monthly to prevent mould and odour build-up.
Run a maintenance wash at 60 degrees Celsius with a drum
cleaning tablet every 3 months.
The filter should be checked and cleaned after every 10 cycles to maintain
drainage performance.
Descale the appliance every 3 months in hard water areas using a Bosch-approved descaling
agent.
Error Codes & Troubleshooting
Error codes on the Bosch HRA578BS6B display indicate
specific faults -- consult the error code table in Appendix A.
E1/F1 errors typically relate to water supply
issues -- check the inlet hose and water pressure.
If the appliance does not start, verify the door is fully
closed and the child lock is not activated.
For persistent faults not resolved by the troubleshooting guide,
contact Bosch customer service with your model and serial number.
Bosch / Appliance
Installation Requirements
The Bosch KFN96VPEA must be installed on a level, stable
surface capable of supporting its full operating weight.
Ensure adequate ventilation clearance as specified in the
installation diagram on page 4.
Connect to a correctly rated power supply -- refer to the data plate for voltage
and amperage requirements.
Plumbing connections (where applicable) must comply with local building regulations and
be completed by a qualified professional.
First Use
Before first use, run the Bosch
KFN96VPEA through an empty cycle to clean the drum and internal components.
Remove all packaging materials,
transit bolts, and protective films before operating.
Set the clock and any regional settings via the control
panel as described in Chapter 2.
Register your appliance on the Bosch website to activate the full manufacturer
warranty.
Operating Programs
The Bosch KFN96VPEA offers a range of programmes designed for
different load types and energy efficiency levels.
Eco mode reduces energy and water consumption by up to 40%
compared to standard cycles.
Quick wash cycles are suitable for lightly soiled loads and complete in under 30
minutes.
Refer to the programme guide in Section 3 for a full list of settings, temperatures, and spin
speeds.
Cleaning & Maintenance
Clean the door seal and detergent drawer of your Bosch
KFN96VPEA monthly to prevent mould and odour build-up.
Run a maintenance wash at 60 degrees Celsius with a drum
cleaning tablet every 3 months.
The filter should be checked and cleaned after every 10 cycles to maintain
drainage performance.
Descale the appliance every 3 months in hard water areas using a Bosch-approved descaling
agent.
Error Codes & Troubleshooting
Error codes on the Bosch KFN96VPEA display indicate
specific faults -- consult the error code table in Appendix A.
E1/F1 errors typically relate to water supply
issues -- check the inlet hose and water pressure.
If the appliance does not start, verify the door is fully
closed and the child lock is not activated.
For persistent faults not resolved by the troubleshooting guide,
contact Bosch customer service with your model and serial number.
Bosch / Appliance
Installation Requirements
The Bosch KGE36AWCA must be installed on a level, stable
surface capable of supporting its full operating weight.
Ensure adequate ventilation clearance as specified in the
installation diagram on page 4.
Connect to a correctly rated power supply -- refer to the data plate for voltage
and amperage requirements.
Plumbing connections (where applicable) must comply with local building regulations and
be completed by a qualified professional.
First Use
Before first use, run the Bosch
KGE36AWCA through an empty cycle to clean the drum and internal components.
Remove all packaging materials,
transit bolts, and protective films before operating.
Set the clock and any regional settings via the control
panel as described in Chapter 2.
Register your appliance on the Bosch website to activate the full manufacturer
warranty.
Operating Programs
The Bosch KGE36AWCA offers a range of programmes designed for
different load types and energy efficiency levels.
Eco mode reduces energy and water consumption by up to 40%
compared to standard cycles.
Quick wash cycles are suitable for lightly soiled loads and complete in under 30
minutes.
Refer to the programme guide in Section 3 for a full list of settings, temperatures, and spin
speeds.
Cleaning & Maintenance
Clean the door seal and detergent drawer of your Bosch
KGE36AWCA monthly to prevent mould and odour build-up.
Run a maintenance wash at 60 degrees Celsius with a drum
cleaning tablet every 3 months.
The filter should be checked and cleaned after every 10 cycles to maintain
drainage performance.
Descale the appliance every 3 months in hard water areas using a Bosch-approved descaling
agent.
Error Codes & Troubleshooting
Error codes on the Bosch KGE36AWCA display indicate
specific faults -- consult the error code table in Appendix A.
E1/F1 errors typically relate to water supply
issues -- check the inlet hose and water pressure.
If the appliance does not start, verify the door is fully
closed and the child lock is not activated.
For persistent faults not resolved by the troubleshooting guide,
contact Bosch customer service with your model and serial number.
Bosch / Appliance
Installation Requirements
The Bosch KGN39XIDR must be installed on a level, stable
surface capable of supporting its full operating weight.
Ensure adequate ventilation clearance as specified in the
installation diagram on page 4.
Connect to a correctly rated power supply -- refer to the data plate for voltage
and amperage requirements.
Plumbing connections (where applicable) must comply with local building regulations and
be completed by a qualified professional.
First Use
Before first use, run the Bosch
KGN39XIDR through an empty cycle to clean the drum and internal components.
Remove all packaging materials,
transit bolts, and protective films before operating.
Set the clock and any regional settings via the control
panel as described in Chapter 2.
Register your appliance on the Bosch website to activate the full manufacturer
warranty.
Operating Programs
The Bosch KGN39XIDR offers a range of programmes designed for
different load types and energy efficiency levels.
Eco mode reduces energy and water consumption by up to 40%
compared to standard cycles.
Quick wash cycles are suitable for lightly soiled loads and complete in under 30
minutes.
Refer to the programme guide in Section 3 for a full list of settings, temperatures, and spin
speeds.
Cleaning & Maintenance
Clean the door seal and detergent drawer of your Bosch
KGN39XIDR monthly to prevent mould and odour build-up.
Run a maintenance wash at 60 degrees Celsius with a drum
cleaning tablet every 3 months.
The filter should be checked and cleaned after every 10 cycles to maintain
drainage performance.
Descale the appliance every 3 months in hard water areas using a Bosch-approved descaling
agent.
Error Codes & Troubleshooting
Error codes on the Bosch KGN39XIDR display indicate
specific faults -- consult the error code table in Appendix A.
E1/F1 errors typically relate to water supply
issues -- check the inlet hose and water pressure.
If the appliance does not start, verify the door is fully
closed and the child lock is not activated.
For persistent faults not resolved by the troubleshooting guide,
contact Bosch customer service with your model and serial number.
Bosch / Appliance
Installation Requirements
The Bosch KGN86AIDR must be installed on a level, stable
surface capable of supporting its full operating weight.
Ensure adequate ventilation clearance as specified in the
installation diagram on page 4.
Connect to a correctly rated power supply -- refer to the data plate for voltage
and amperage requirements.
Plumbing connections (where applicable) must comply with local building regulations and
be completed by a qualified professional.
First Use
Before first use, run the Bosch
KGN86AIDR through an empty cycle to clean the drum and internal components.
Remove all packaging materials,
transit bolts, and protective films before operating.
Set the clock and any regional settings via the control
panel as described in Chapter 2.
Register your appliance on the Bosch website to activate the full manufacturer
warranty.
Operating Programs
The Bosch KGN86AIDR offers a range of programmes designed for
different load types and energy efficiency levels.
Eco mode reduces energy and water consumption by up to 40%
compared to standard cycles.
Quick wash cycles are suitable for lightly soiled loads and complete in under 30
minutes.
Refer to the programme guide in Section 3 for a full list of settings, temperatures, and spin
speeds.
Cleaning & Maintenance
Clean the door seal and detergent drawer of your Bosch
KGN86AIDR monthly to prevent mould and odour build-up.
Run a maintenance wash at 60 degrees Celsius with a drum
cleaning tablet every 3 months.
The filter should be checked and cleaned after every 10 cycles to maintain
drainage performance.
Descale the appliance every 3 months in hard water areas using a Bosch-approved descaling
agent.
Error Codes & Troubleshooting
Error codes on the Bosch KGN86AIDR display indicate
specific faults -- consult the error code table in Appendix A.
E1/F1 errors typically relate to water supply
issues -- check the inlet hose and water pressure.
If the appliance does not start, verify the door is fully
closed and the child lock is not activated.
For persistent faults not resolved by the troubleshooting guide,
contact Bosch customer service with your model and serial number.
Bosch / Appliance
Installation Requirements
The Bosch MBM4HRM20 must be installed on a level, stable
surface capable of supporting its full operating weight.
Ensure adequate ventilation clearance as specified in the
installation diagram on page 4.
Connect to a correctly rated power supply -- refer to the data plate for voltage
and amperage requirements.
Plumbing connections (where applicable) must comply with local building regulations and
be completed by a qualified professional.
First Use
Before first use, run the Bosch
MBM4HRM20 through an empty cycle to clean the drum and internal components.
Remove all packaging materials,
transit bolts, and protective films before operating.
Set the clock and any regional settings via the control
panel as described in Chapter 2.
Register your appliance on the Bosch website to activate the full manufacturer
warranty.
Operating Programs
The Bosch MBM4HRM20 offers a range of programmes designed for
different load types and energy efficiency levels.
Eco mode reduces energy and water consumption by up to 40%
compared to standard cycles.
Quick wash cycles are suitable for lightly soiled loads and complete in under 30
minutes.
Refer to the programme guide in Section 3 for a full list of settings, temperatures, and spin
speeds.
Cleaning & Maintenance
Clean the door seal and detergent drawer of your Bosch
MBM4HRM20 monthly to prevent mould and odour build-up.
Run a maintenance wash at 60 degrees Celsius with a drum
cleaning tablet every 3 months.
The filter should be checked and cleaned after every 10 cycles to maintain
drainage performance.
Descale the appliance every 3 months in hard water areas using a Bosch-approved descaling
agent.
Error Codes & Troubleshooting
Error codes on the Bosch MBM4HRM20 display indicate
specific faults -- consult the error code table in Appendix A.
E1/F1 errors typically relate to water supply
issues -- check the inlet hose and water pressure.
If the appliance does not start, verify the door is fully
closed and the child lock is not activated.
For persistent faults not resolved by the troubleshooting guide,
contact Bosch customer service with your model and serial number.
Bosch / Appliance
Installation Requirements
The Bosch MCM68840 must be installed on a level, stable
surface capable of supporting its full operating weight.
Ensure adequate ventilation clearance as specified in the
installation diagram on page 4.
Connect to a correctly rated power supply -- refer to the data plate for voltage
and amperage requirements.
Plumbing connections (where applicable) must comply with local building regulations and
be completed by a qualified professional.
First Use
Before first use, run the Bosch
MCM68840 through an empty cycle to clean the drum and internal components.
Remove all packaging materials, transit
bolts, and protective films before operating.
Set the clock and any regional settings via the control panel as
described in Chapter 2.
Register your appliance on the Bosch website to activate the full manufacturer
warranty.
Operating Programs
The Bosch MCM68840 offers a range of programmes designed for
different load types and energy efficiency levels.
Eco mode reduces energy and water consumption by up to 40%
compared to standard cycles.
Quick wash cycles are suitable for lightly soiled loads and complete in under 30
minutes.
Refer to the programme guide in Section 3 for a full list of settings, temperatures, and spin
speeds.
Cleaning & Maintenance
Clean the door seal and detergent drawer of your Bosch
MCM68840 monthly to prevent mould and odour build-up.
Run a maintenance wash at 60 degrees Celsius with a drum
cleaning tablet every 3 months.
The filter should be checked and cleaned after every 10 cycles to maintain
drainage performance.
Descale the appliance every 3 months in hard water areas using a Bosch-approved descaling
agent.
Error Codes & Troubleshooting
Error codes on the Bosch MCM68840 display indicate
specific faults -- consult the error code table in Appendix A.
E1/F1 errors typically relate to water supply
issues -- check the inlet hose and water pressure.
If the appliance does not start, verify the door is fully
closed and the child lock is not activated.
For persistent faults not resolved by the troubleshooting guide,
contact Bosch customer service with your model and serial number.
Bosch / Appliance
Installation Requirements
The Bosch MFQ36480 must be installed on a level, stable
surface capable of supporting its full operating weight.
Ensure adequate ventilation clearance as specified in the
installation diagram on page 4.
Connect to a correctly rated power supply -- refer to the data plate for voltage
and amperage requirements.
Plumbing connections (where applicable) must comply with local building regulations and
be completed by a qualified professional.
First Use
Before first use, run the Bosch
MFQ36480 through an empty cycle to clean the drum and internal components.
Remove all packaging materials, transit
bolts, and protective films before operating.
Set the clock and any regional settings via the control panel as
described in Chapter 2.
Register your appliance on the Bosch website to activate the full manufacturer
warranty.
Operating Programs
The Bosch MFQ36480 offers a range of programmes designed for
different load types and energy efficiency levels.
Eco mode reduces energy and water consumption by up to 40%
compared to standard cycles.
Quick wash cycles are suitable for lightly soiled loads and complete in under 30
minutes.
Refer to the programme guide in Section 3 for a full list of settings, temperatures, and spin
speeds.
Cleaning & Maintenance
Clean the door seal and detergent drawer of your Bosch
MFQ36480 monthly to prevent mould and odour build-up.
Run a maintenance wash at 60 degrees Celsius with a drum
cleaning tablet every 3 months.
The filter should be checked and cleaned after every 10 cycles to maintain
drainage performance.
Descale the appliance every 3 months in hard water areas using a Bosch-approved descaling
agent.
Error Codes & Troubleshooting
Error codes on the Bosch MFQ36480 display indicate
specific faults -- consult the error code table in Appendix A.
E1/F1 errors typically relate to water supply
issues -- check the inlet hose and water pressure.
If the appliance does not start, verify the door is fully
closed and the child lock is not activated.
For persistent faults not resolved by the troubleshooting guide,
contact Bosch customer service with your model and serial number.
Bosch / Appliance
Installation Requirements
The Bosch MFQ4060X must be installed on a level, stable
surface capable of supporting its full operating weight.
Ensure adequate ventilation clearance as specified in the
installation diagram on page 4.
Connect to a correctly rated power supply -- refer to the data plate for voltage
and amperage requirements.
Plumbing connections (where applicable) must comply with local building regulations and
be completed by a qualified professional.
First Use
Before first use, run the Bosch
MFQ4060X through an empty cycle to clean the drum and internal components.
Remove all packaging materials, transit
bolts, and protective films before operating.
Set the clock and any regional settings via the control panel as
described in Chapter 2.
Register your appliance on the Bosch website to activate the full manufacturer
warranty.
Operating Programs
The Bosch MFQ4060X offers a range of programmes designed for
different load types and energy efficiency levels.
Eco mode reduces energy and water consumption by up to 40%
compared to standard cycles.
Quick wash cycles are suitable for lightly soiled loads and complete in under 30
minutes.
Refer to the programme guide in Section 3 for a full list of settings, temperatures, and spin
speeds.
Cleaning & Maintenance
Clean the door seal and detergent drawer of your Bosch
MFQ4060X monthly to prevent mould and odour build-up.
Run a maintenance wash at 60 degrees Celsius with a drum
cleaning tablet every 3 months.
The filter should be checked and cleaned after every 10 cycles to maintain
drainage performance.
Descale the appliance every 3 months in hard water areas using a Bosch-approved descaling
agent.
Error Codes & Troubleshooting
Error codes on the Bosch MFQ4060X display indicate
specific faults -- consult the error code table in Appendix A.
E1/F1 errors typically relate to water supply
issues -- check the inlet hose and water pressure.
If the appliance does not start, verify the door is fully
closed and the child lock is not activated.
For persistent faults not resolved by the troubleshooting guide,
contact Bosch customer service with your model and serial number.
Bosch / Appliance
Installation Requirements
The Bosch MMBH6P6B must be installed on a level, stable
surface capable of supporting its full operating weight.
Ensure adequate ventilation clearance as specified in the
installation diagram on page 4.
Connect to a correctly rated power supply -- refer to the data plate for voltage
and amperage requirements.
Plumbing connections (where applicable) must comply with local building regulations and
be completed by a qualified professional.
First Use
Before first use, run the Bosch
MMBH6P6B through an empty cycle to clean the drum and internal components.
Remove all packaging materials, transit
bolts, and protective films before operating.
Set the clock and any regional settings via the control panel as
described in Chapter 2.
Register your appliance on the Bosch website to activate the full manufacturer
warranty.
Operating Programs
The Bosch MMBH6P6B offers a range of programmes designed for
different load types and energy efficiency levels.
Eco mode reduces energy and water consumption by up to 40%
compared to standard cycles.
Quick wash cycles are suitable for lightly soiled loads and complete in under 30
minutes.
Refer to the programme guide in Section 3 for a full list of settings, temperatures, and spin
speeds.
Cleaning & Maintenance
Clean the door seal and detergent drawer of your Bosch
MMBH6P6B monthly to prevent mould and odour build-up.
Run a maintenance wash at 60 degrees Celsius with a drum
cleaning tablet every 3 months.
The filter should be checked and cleaned after every 10 cycles to maintain
drainage performance.
Descale the appliance every 3 months in hard water areas using a Bosch-approved descaling
agent.
Error Codes & Troubleshooting
Error codes on the Bosch MMBH6P6B display indicate
specific faults -- consult the error code table in Appendix A.
E1/F1 errors typically relate to water supply
issues -- check the inlet hose and water pressure.
If the appliance does not start, verify the door is fully
closed and the child lock is not activated.
For persistent faults not resolved by the troubleshooting guide,
contact Bosch customer service with your model and serial number.
Bosch / Appliance
Installation Requirements
The Bosch MUM54251 must be installed on a level, stable
surface capable of supporting its full operating weight.
Ensure adequate ventilation clearance as specified in the
installation diagram on page 4.
Connect to a correctly rated power supply -- refer to the data plate for voltage
and amperage requirements.
Plumbing connections (where applicable) must comply with local building regulations and
be completed by a qualified professional.
First Use
Before first use, run the Bosch
MUM54251 through an empty cycle to clean the drum and internal components.
Remove all packaging materials, transit
bolts, and protective films before operating.
Set the clock and any regional settings via the control panel as
described in Chapter 2.
Register your appliance on the Bosch website to activate the full manufacturer
warranty.
Operating Programs
The Bosch MUM54251 offers a range of programmes designed for
different load types and energy efficiency levels.
Eco mode reduces energy and water consumption by up to 40%
compared to standard cycles.
Quick wash cycles are suitable for lightly soiled loads and complete in under 30
minutes.
Refer to the programme guide in Section 3 for a full list of settings, temperatures, and spin
speeds.
Cleaning & Maintenance
Clean the door seal and detergent drawer of your Bosch
MUM54251 monthly to prevent mould and odour build-up.
Run a maintenance wash at 60 degrees Celsius with a drum
cleaning tablet every 3 months.
The filter should be checked and cleaned after every 10 cycles to maintain
drainage performance.
Descale the appliance every 3 months in hard water areas using a Bosch-approved descaling
agent.
Error Codes & Troubleshooting
Error codes on the Bosch MUM54251 display indicate
specific faults -- consult the error code table in Appendix A.
E1/F1 errors typically relate to water supply
issues -- check the inlet hose and water pressure.
If the appliance does not start, verify the door is fully
closed and the child lock is not activated.
For persistent faults not resolved by the troubleshooting guide,
contact Bosch customer service with your model and serial number.
Bosch / Appliance
Installation Requirements
The Bosch PKN875DP1D must be installed on a level,
stable surface capable of supporting its full operating weight.
Ensure adequate ventilation clearance as specified
in the installation diagram on page 4.
Connect to a correctly rated power supply -- refer to the data plate for
voltage and amperage requirements.
Plumbing connections (where applicable) must comply with local building
regulations and be completed by a qualified professional.
First Use
Before first use, run
the Bosch PKN875DP1D through an empty cycle to clean the drum and internal components.
Remove all packaging
materials, transit bolts, and protective films before operating.
Set the clock and any regional settings via the
control panel as described in Chapter 2.
Register your appliance on the Bosch website to activate the full
manufacturer warranty.
Operating Programs
The Bosch PKN875DP1D offers a range of programmes
designed for different load types and energy efficiency levels.
Eco mode reduces energy and water consumption by
up to 40% compared to standard cycles.
Quick wash cycles are suitable for lightly soiled loads and complete in
under 30 minutes.
Refer to the programme guide in Section 3 for a full list of settings, temperatures, and spin
speeds.
Cleaning & Maintenance
Clean the door seal and detergent drawer of your Bosch
PKN875DP1D monthly to prevent mould and odour build-up.
Run a maintenance wash at 60 degrees Celsius with a drum
cleaning tablet every 3 months.
The filter should be checked and cleaned after every 10 cycles to maintain
drainage performance.
Descale the appliance every 3 months in hard water areas using a Bosch-approved descaling
agent.
Error Codes & Troubleshooting
Error codes on the Bosch PKN875DP1D display indicate
specific faults -- consult the error code table in Appendix A.
E1/F1 errors typically relate to water supply
issues -- check the inlet hose and water pressure.
If the appliance does not start, verify the door is fully
closed and the child lock is not activated.
For persistent faults not resolved by the troubleshooting guide,
contact Bosch customer service with your model and serial number.
Bosch / Appliance
Installation Requirements
The Bosch PXX875DC1E must be installed on a level,
stable surface capable of supporting its full operating weight.
Ensure adequate ventilation clearance as specified
in the installation diagram on page 4.
Connect to a correctly rated power supply -- refer to the data plate for
voltage and amperage requirements.
Plumbing connections (where applicable) must comply with local building
regulations and be completed by a qualified professional.
First Use
Before first use, run
the Bosch PXX875DC1E through an empty cycle to clean the drum and internal components.
Remove all packaging
materials, transit bolts, and protective films before operating.
Set the clock and any regional settings via the
control panel as described in Chapter 2.
Register your appliance on the Bosch website to activate the full
manufacturer warranty.
Operating Programs
The Bosch PXX875DC1E offers a range of programmes
designed for different load types and energy efficiency levels.
Eco mode reduces energy and water consumption by
up to 40% compared to standard cycles.
Quick wash cycles are suitable for lightly soiled loads and complete in
under 30 minutes.
Refer to the programme guide in Section 3 for a full list of settings, temperatures, and spin
speeds.
Cleaning & Maintenance
Clean the door seal and detergent drawer of your Bosch
PXX875DC1E monthly to prevent mould and odour build-up.
Run a maintenance wash at 60 degrees Celsius with a drum
cleaning tablet every 3 months.
The filter should be checked and cleaned after every 10 cycles to maintain
drainage performance.
Descale the appliance every 3 months in hard water areas using a Bosch-approved descaling
agent.
Error Codes & Troubleshooting
Error codes on the Bosch PXX875DC1E display indicate
specific faults -- consult the error code table in Appendix A.
E1/F1 errors typically relate to water supply
issues -- check the inlet hose and water pressure.
If the appliance does not start, verify the door is fully
closed and the child lock is not activated.
For persistent faults not resolved by the troubleshooting guide,
contact Bosch customer service with your model and serial number.
Bosch / Appliance
Installation Requirements
The Bosch SMS2HTW72E must be installed on a level,
stable surface capable of supporting its full operating weight.
Ensure adequate ventilation clearance as specified
in the installation diagram on page 4.
Connect to a correctly rated power supply -- refer to the data plate for
voltage and amperage requirements.
Plumbing connections (where applicable) must comply with local building
regulations and be completed by a qualified professional.
First Use
Before first use, run
the Bosch SMS2HTW72E through an empty cycle to clean the drum and internal components.
Remove all packaging
materials, transit bolts, and protective films before operating.
Set the clock and any regional settings via the
control panel as described in Chapter 2.
Register your appliance on the Bosch website to activate the full
manufacturer warranty.
Operating Programs
The Bosch SMS2HTW72E offers a range of programmes
designed for different load types and energy efficiency levels.
Eco mode reduces energy and water consumption by
up to 40% compared to standard cycles.
Quick wash cycles are suitable for lightly soiled loads and complete in
under 30 minutes.
Refer to the programme guide in Section 3 for a full list of settings, temperatures, and spin
speeds.
Cleaning & Maintenance
Clean the door seal and detergent drawer of your Bosch
SMS2HTW72E monthly to prevent mould and odour build-up.
Run a maintenance wash at 60 degrees Celsius with a drum
cleaning tablet every 3 months.
The filter should be checked and cleaned after every 10 cycles to maintain
drainage performance.
Descale the appliance every 3 months in hard water areas using a Bosch-approved descaling
agent.
Error Codes & Troubleshooting
Error codes on the Bosch SMS2HTW72E display indicate
specific faults -- consult the error code table in Appendix A.
E1/F1 errors typically relate to water supply
issues -- check the inlet hose and water pressure.
If the appliance does not start, verify the door is fully
closed and the child lock is not activated.
For persistent faults not resolved by the troubleshooting guide,
contact Bosch customer service with your model and serial number.
Bosch / Appliance
Installation Requirements
The Bosch SMS8YCI01E must be installed on a level,
stable surface capable of supporting its full operating weight.
Ensure adequate ventilation clearance as specified
in the installation diagram on page 4.
Connect to a correctly rated power supply -- refer to the data plate for
voltage and amperage requirements.
Plumbing connections (where applicable) must comply with local building
regulations and be completed by a qualified professional.
First Use
Before first use, run
the Bosch SMS8YCI01E through an empty cycle to clean the drum and internal components.
Remove all packaging
materials, transit bolts, and protective films before operating.
Set the clock and any regional settings via the
control panel as described in Chapter 2.
Register your appliance on the Bosch website to activate the full
manufacturer warranty.
Operating Programs
The Bosch SMS8YCI01E offers a range of programmes
designed for different load types and energy efficiency levels.
Eco mode reduces energy and water consumption by
up to 40% compared to standard cycles.
Quick wash cycles are suitable for lightly soiled loads and complete in
under 30 minutes.
Refer to the programme guide in Section 3 for a full list of settings, temperatures, and spin
speeds.
Cleaning & Maintenance
Clean the door seal and detergent drawer of your Bosch
SMS8YCI01E monthly to prevent mould and odour build-up.
Run a maintenance wash at 60 degrees Celsius with a drum
cleaning tablet every 3 months.
The filter should be checked and cleaned after every 10 cycles to maintain
drainage performance.
Descale the appliance every 3 months in hard water areas using a Bosch-approved descaling
agent.
Error Codes & Troubleshooting
Error codes on the Bosch SMS8YCI01E display indicate
specific faults -- consult the error code table in Appendix A.
E1/F1 errors typically relate to water supply
issues -- check the inlet hose and water pressure.
If the appliance does not start, verify the door is fully
closed and the child lock is not activated.
For persistent faults not resolved by the troubleshooting guide,
contact Bosch customer service with your model and serial number.
Bosch / Appliance
Installation Requirements
The Bosch SMV6ZCX07E must be installed on a level,
stable surface capable of supporting its full operating weight.
Ensure adequate ventilation clearance as specified
in the installation diagram on page 4.
Connect to a correctly rated power supply -- refer to the data plate for
voltage and amperage requirements.
Plumbing connections (where applicable) must comply with local building
regulations and be completed by a qualified professional.
First Use
Before first use, run
the Bosch SMV6ZCX07E through an empty cycle to clean the drum and internal components.
Remove all packaging
materials, transit bolts, and protective films before operating.
Set the clock and any regional settings via the
control panel as described in Chapter 2.
Register your appliance on the Bosch website to activate the full
manufacturer warranty.
Operating Programs
The Bosch SMV6ZCX07E offers a range of programmes
designed for different load types and energy efficiency levels.
Eco mode reduces energy and water consumption by
up to 40% compared to standard cycles.
Quick wash cycles are suitable for lightly soiled loads and complete in
under 30 minutes.
Refer to the programme guide in Section 3 for a full list of settings, temperatures, and spin
speeds.
Cleaning & Maintenance
Clean the door seal and detergent drawer of your Bosch
SMV6ZCX07E monthly to prevent mould and odour build-up.
Run a maintenance wash at 60 degrees Celsius with a drum
cleaning tablet every 3 months.
The filter should be checked and cleaned after every 10 cycles to maintain
drainage performance.
Descale the appliance every 3 months in hard water areas using a Bosch-approved descaling
agent.
Error Codes & Troubleshooting
Error codes on the Bosch SMV6ZCX07E display indicate
specific faults -- consult the error code table in Appendix A.
E1/F1 errors typically relate to water supply
issues -- check the inlet hose and water pressure.
If the appliance does not start, verify the door is fully
closed and the child lock is not activated.
For persistent faults not resolved by the troubleshooting guide,
contact Bosch customer service with your model and serial number.
Bosch / Appliance
Installation Requirements
The Bosch SPI46IS00E must be installed on a level,
stable surface capable of supporting its full operating weight.
Ensure adequate ventilation clearance as specified
in the installation diagram on page 4.
Connect to a correctly rated power supply -- refer to the data plate for
voltage and amperage requirements.
Plumbing connections (where applicable) must comply with local building
regulations and be completed by a qualified professional.
First Use
Before first use, run
the Bosch SPI46IS00E through an empty cycle to clean the drum and internal components.
Remove all packaging
materials, transit bolts, and protective films before operating.
Set the clock and any regional settings via the
control panel as described in Chapter 2.
Register your appliance on the Bosch website to activate the full
manufacturer warranty.
Operating Programs
The Bosch SPI46IS00E offers a range of programmes
designed for different load types and energy efficiency levels.
Eco mode reduces energy and water consumption by
up to 40% compared to standard cycles.
Quick wash cycles are suitable for lightly soiled loads and complete in
under 30 minutes.
Refer to the programme guide in Section 3 for a full list of settings, temperatures, and spin
speeds.
Cleaning & Maintenance
Clean the door seal and detergent drawer of your Bosch
SPI46IS00E monthly to prevent mould and odour build-up.
Run a maintenance wash at 60 degrees Celsius with a drum
cleaning tablet every 3 months.
The filter should be checked and cleaned after every 10 cycles to maintain
drainage performance.
Descale the appliance every 3 months in hard water areas using a Bosch-approved descaling
agent.
Error Codes & Troubleshooting
Error codes on the Bosch SPI46IS00E display indicate
specific faults -- consult the error code table in Appendix A.
E1/F1 errors typically relate to water supply
issues -- check the inlet hose and water pressure.
If the appliance does not start, verify the door is fully
closed and the child lock is not activated.
For persistent faults not resolved by the troubleshooting guide,
contact Bosch customer service with your model and serial number.
Bosch / Appliance
Installation Requirements
The Bosch SPV4HMX10E must be installed on a level,
stable surface capable of supporting its full operating weight.
Ensure adequate ventilation clearance as specified
in the installation diagram on page 4.
Connect to a correctly rated power supply -- refer to the data plate for
voltage and amperage requirements.
Plumbing connections (where applicable) must comply with local building
regulations and be completed by a qualified professional.
First Use
Before first use, run
the Bosch SPV4HMX10E through an empty cycle to clean the drum and internal components.
Remove all packaging
materials, transit bolts, and protective films before operating.
Set the clock and any regional settings via the
control panel as described in Chapter 2.
Register your appliance on the Bosch website to activate the full
manufacturer warranty.
Operating Programs
The Bosch SPV4HMX10E offers a range of programmes
designed for different load types and energy efficiency levels.
Eco mode reduces energy and water consumption by
up to 40% compared to standard cycles.
Quick wash cycles are suitable for lightly soiled loads and complete in
under 30 minutes.
Refer to the programme guide in Section 3 for a full list of settings, temperatures, and spin
speeds.
Cleaning & Maintenance
Clean the door seal and detergent drawer of your Bosch
SPV4HMX10E monthly to prevent mould and odour build-up.
Run a maintenance wash at 60 degrees Celsius with a drum
cleaning tablet every 3 months.
The filter should be checked and cleaned after every 10 cycles to maintain
drainage performance.
Descale the appliance every 3 months in hard water areas using a Bosch-approved descaling
agent.
Error Codes & Troubleshooting
Error codes on the Bosch SPV4HMX10E display indicate
specific faults -- consult the error code table in Appendix A.
E1/F1 errors typically relate to water supply
issues -- check the inlet hose and water pressure.
If the appliance does not start, verify the door is fully
closed and the child lock is not activated.
For persistent faults not resolved by the troubleshooting guide,
contact Bosch customer service with your model and serial number.
Bosch / Appliance
Installation Requirements
The Bosch TIS65429RW must be installed on a level,
stable surface capable of supporting its full operating weight.
Ensure adequate ventilation clearance as specified
in the installation diagram on page 4.
Connect to a correctly rated power supply -- refer to the data plate for
voltage and amperage requirements.
Plumbing connections (where applicable) must comply with local building
regulations and be completed by a qualified professional.
First Use
Before first use, run
the Bosch TIS65429RW through an empty cycle to clean the drum and internal components.
Remove all packaging
materials, transit bolts, and protective films before operating.
Set the clock and any regional settings via the
control panel as described in Chapter 2.
Register your appliance on the Bosch website to activate the full
manufacturer warranty.
Operating Programs
The Bosch TIS65429RW offers a range of programmes
designed for different load types and energy efficiency levels.
Eco mode reduces energy and water consumption by
up to 40% compared to standard cycles.
Quick wash cycles are suitable for lightly soiled loads and complete in
under 30 minutes.
Refer to the programme guide in Section 3 for a full list of settings, temperatures, and spin
speeds.
Cleaning & Maintenance
Clean the door seal and detergent drawer of your Bosch
TIS65429RW monthly to prevent mould and odour build-up.
Run a maintenance wash at 60 degrees Celsius with a drum
cleaning tablet every 3 months.
The filter should be checked and cleaned after every 10 cycles to maintain
drainage performance.
Descale the appliance every 3 months in hard water areas using a Bosch-approved descaling
agent.
Error Codes & Troubleshooting
Error codes on the Bosch TIS65429RW display indicate
specific faults -- consult the error code table in Appendix A.
E1/F1 errors typically relate to water supply
issues -- check the inlet hose and water pressure.
If the appliance does not start, verify the door is fully
closed and the child lock is not activated.
For persistent faults not resolved by the troubleshooting guide,
contact Bosch customer service with your model and serial number.
Bosch / Appliance
Installation Requirements
The Bosch TSM6A011R must be installed on a level, stable
surface capable of supporting its full operating weight.
Ensure adequate ventilation clearance as specified in the
installation diagram on page 4.
Connect to a correctly rated power supply -- refer to the data plate for voltage
and amperage requirements.
Plumbing connections (where applicable) must comply with local building regulations and
be completed by a qualified professional.
First Use
Before first use, run the Bosch
TSM6A011R through an empty cycle to clean the drum and internal components.
Remove all packaging materials,
transit bolts, and protective films before operating.
Set the clock and any regional settings via the control
panel as described in Chapter 2.
Register your appliance on the Bosch website to activate the full manufacturer
warranty.
Operating Programs
The Bosch TSM6A011R offers a range of programmes designed for
different load types and energy efficiency levels.
Eco mode reduces energy and water consumption by up to 40%
compared to standard cycles.
Quick wash cycles are suitable for lightly soiled loads and complete in under 30
minutes.
Refer to the programme guide in Section 3 for a full list of settings, temperatures, and spin
speeds.
Cleaning & Maintenance
Clean the door seal and detergent drawer of your Bosch
TSM6A011R monthly to prevent mould and odour build-up.
Run a maintenance wash at 60 degrees Celsius with a drum
cleaning tablet every 3 months.
The filter should be checked and cleaned after every 10 cycles to maintain
drainage performance.
Descale the appliance every 3 months in hard water areas using a Bosch-approved descaling
agent.
Error Codes & Troubleshooting
Error codes on the Bosch TSM6A011R display indicate
specific faults -- consult the error code table in Appendix A.
E1/F1 errors typically relate to water supply
issues -- check the inlet hose and water pressure.
If the appliance does not start, verify the door is fully
closed and the child lock is not activated.
For persistent faults not resolved by the troubleshooting guide,
contact Bosch customer service with your model and serial number.
Bosch / Appliance
Installation Requirements
The Bosch WAN28281FF must be installed on a level,
stable surface capable of supporting its full operating weight.
Ensure adequate ventilation clearance as specified
in the installation diagram on page 4.
Connect to a correctly rated power supply -- refer to the data plate for
voltage and amperage requirements.
Plumbing connections (where applicable) must comply with local building
regulations and be completed by a qualified professional.
First Use
Before first use, run
the Bosch WAN28281FF through an empty cycle to clean the drum and internal components.
Remove all packaging
materials, transit bolts, and protective films before operating.
Set the clock and any regional settings via the
control panel as described in Chapter 2.
Register your appliance on the Bosch website to activate the full
manufacturer warranty.
Operating Programs
The Bosch WAN28281FF offers a range of programmes
designed for different load types and energy efficiency levels.
Eco mode reduces energy and water consumption by
up to 40% compared to standard cycles.
Quick wash cycles are suitable for lightly soiled loads and complete in
under 30 minutes.
Refer to the programme guide in Section 3 for a full list of settings, temperatures, and spin
speeds.
Cleaning & Maintenance
Clean the door seal and detergent drawer of your Bosch
WAN28281FF monthly to prevent mould and odour build-up.
Run a maintenance wash at 60 degrees Celsius with a drum
cleaning tablet every 3 months.
The filter should be checked and cleaned after every 10 cycles to maintain
drainage performance.
Descale the appliance every 3 months in hard water areas using a Bosch-approved descaling
agent.
Error Codes & Troubleshooting
Error codes on the Bosch WAN28281FF display indicate
specific faults -- consult the error code table in Appendix A.
E1/F1 errors typically relate to water supply
issues -- check the inlet hose and water pressure.
If the appliance does not start, verify the door is fully
closed and the child lock is not activated.
For persistent faults not resolved by the troubleshooting guide,
contact Bosch customer service with your model and serial number.
Bosch / Appliance
Installation Requirements
The Bosch WAX32EH0FF must be installed on a level,
stable surface capable of supporting its full operating weight.
Ensure adequate ventilation clearance as specified
in the installation diagram on page 4.
Connect to a correctly rated power supply -- refer to the data plate for
voltage and amperage requirements.
Plumbing connections (where applicable) must comply with local building
regulations and be completed by a qualified professional.
First Use
Before first use, run
the Bosch WAX32EH0FF through an empty cycle to clean the drum and internal components.
Remove all packaging
materials, transit bolts, and protective films before operating.
Set the clock and any regional settings via the
control panel as described in Chapter 2.
Register your appliance on the Bosch website to activate the full
manufacturer warranty.
Operating Programs
The Bosch WAX32EH0FF offers a range of programmes
designed for different load types and energy efficiency levels.
Eco mode reduces energy and water consumption by
up to 40% compared to standard cycles.
Quick wash cycles are suitable for lightly soiled loads and complete in
under 30 minutes.
Refer to the programme guide in Section 3 for a full list of settings, temperatures, and spin
speeds.
Cleaning & Maintenance
Clean the door seal and detergent drawer of your Bosch
WAX32EH0FF monthly to prevent mould and odour build-up.
Run a maintenance wash at 60 degrees Celsius with a drum
cleaning tablet every 3 months.
The filter should be checked and cleaned after every 10 cycles to maintain
drainage performance.
Descale the appliance every 3 months in hard water areas using a Bosch-approved descaling
agent.
Error Codes & Troubleshooting
Error codes on the Bosch WAX32EH0FF display indicate
specific faults -- consult the error code table in Appendix A.
E1/F1 errors typically relate to water supply
issues -- check the inlet hose and water pressure.
If the appliance does not start, verify the door is fully
closed and the child lock is not activated.
For persistent faults not resolved by the troubleshooting guide,
contact Bosch customer service with your model and serial number.
Bosch / Appliance
Installation Requirements
The Bosch WGG25401FF must be installed on a level,
stable surface capable of supporting its full operating weight.
Ensure adequate ventilation clearance as specified
in the installation diagram on page 4.
Connect to a correctly rated power supply -- refer to the data plate for
voltage and amperage requirements.
Plumbing connections (where applicable) must comply with local building
regulations and be completed by a qualified professional.
First Use
Before first use, run
the Bosch WGG25401FF through an empty cycle to clean the drum and internal components.
Remove all packaging
materials, transit bolts, and protective films before operating.
Set the clock and any regional settings via the
control panel as described in Chapter 2.
Register your appliance on the Bosch website to activate the full
manufacturer warranty.
Operating Programs
The Bosch WGG25401FF offers a range of programmes
designed for different load types and energy efficiency levels.
Eco mode reduces energy and water consumption by
up to 40% compared to standard cycles.
Quick wash cycles are suitable for lightly soiled loads and complete in
under 30 minutes.
Refer to the programme guide in Section 3 for a full list of settings, temperatures, and spin
speeds.
Cleaning & Maintenance
Clean the door seal and detergent drawer of your Bosch
WGG25401FF monthly to prevent mould and odour build-up.
Run a maintenance wash at 60 degrees Celsius with a drum
cleaning tablet every 3 months.
The filter should be checked and cleaned after every 10 cycles to maintain
drainage performance.
Descale the appliance every 3 months in hard water areas using a Bosch-approved descaling
agent.
Error Codes & Troubleshooting
Error codes on the Bosch WGG25401FF display indicate
specific faults -- consult the error code table in Appendix A.
E1/F1 errors typically relate to water supply
issues -- check the inlet hose and water pressure.
If the appliance does not start, verify the door is fully
closed and the child lock is not activated.
For persistent faults not resolved by the troubleshooting guide,
contact Bosch customer service with your model and serial number.
Bosch / Appliance
Installation Requirements
The Bosch WQG245BSFF must be installed on a level,
stable surface capable of supporting its full operating weight.
Ensure adequate ventilation clearance as specified
in the installation diagram on page 4.
Connect to a correctly rated power supply -- refer to the data plate for
voltage and amperage requirements.
Plumbing connections (where applicable) must comply with local building
regulations and be completed by a qualified professional.
First Use
Before first use, run
the Bosch WQG245BSFF through an empty cycle to clean the drum and internal components.
Remove all packaging
materials, transit bolts, and protective films before operating.
Set the clock and any regional settings via the
control panel as described in Chapter 2.
Register your appliance on the Bosch website to activate the full
manufacturer warranty.
Operating Programs
The Bosch WQG245BSFF offers a range of programmes
designed for different load types and energy efficiency levels.
Eco mode reduces energy and water consumption by
up to 40% compared to standard cycles.
Quick wash cycles are suitable for lightly soiled loads and complete in
under 30 minutes.
Refer to the programme guide in Section 3 for a full list of settings, temperatures, and spin
speeds.
Cleaning & Maintenance
Clean the door seal and detergent drawer of your Bosch
WQG245BSFF monthly to prevent mould and odour build-up.
Run a maintenance wash at 60 degrees Celsius with a drum
cleaning tablet every 3 months.
The filter should be checked and cleaned after every 10 cycles to maintain
drainage performance.
Descale the appliance every 3 months in hard water areas using a Bosch-approved descaling
agent.
Error Codes & Troubleshooting
Error codes on the Bosch WQG245BSFF display indicate
specific faults -- consult the error code table in Appendix A.
E1/F1 errors typically relate to water supply
issues -- check the inlet hose and water pressure.
If the appliance does not start, verify the door is fully
closed and the child lock is not activated.
For persistent faults not resolved by the troubleshooting guide,
contact Bosch customer service with your model and serial number.
Bosch / Appliance
Installation Requirements
The Bosch WTX87EH0FF must be installed on a level,
stable surface capable of supporting its full operating weight.
Ensure adequate ventilation clearance as specified
in the installation diagram on page 4.
Connect to a correctly rated power supply -- refer to the data plate for
voltage and amperage requirements.
Plumbing connections (where applicable) must comply with local building
regulations and be completed by a qualified professional.
First Use
Before first use, run
the Bosch WTX87EH0FF through an empty cycle to clean the drum and internal components.
Remove all packaging
materials, transit bolts, and protective films before operating.
Set the clock and any regional settings via the
control panel as described in Chapter 2.
Register your appliance on the Bosch website to activate the full
manufacturer warranty.
Operating Programs
The Bosch WTX87EH0FF offers a range of programmes
designed for different load types and energy efficiency levels.
Eco mode reduces energy and water consumption by
up to 40% compared to standard cycles.
Quick wash cycles are suitable for lightly soiled loads and complete in
under 30 minutes.
Refer to the programme guide in Section 3 for a full list of settings, temperatures, and spin
speeds.
Cleaning & Maintenance
Clean the door seal and detergent drawer of your Bosch
WTX87EH0FF monthly to prevent mould and odour build-up.
Run a maintenance wash at 60 degrees Celsius with a drum
cleaning tablet every 3 months.
The filter should be checked and cleaned after every 10 cycles to maintain
drainage performance.
Descale the appliance every 3 months in hard water areas using a Bosch-approved descaling
agent.
Error Codes & Troubleshooting
Error codes on the Bosch WTX87EH0FF display indicate
specific faults -- consult the error code table in Appendix A.
E1/F1 errors typically relate to water supply
issues -- check the inlet hose and water pressure.
If the appliance does not start, verify the door is fully
closed and the child lock is not activated.
For persistent faults not resolved by the troubleshooting guide,
contact Bosch customer service with your model and serial number.
Bosch / Appliance